How to Hang Bikes from the Ceiling

While bikes are convenient and useful ways to get exercise, they arent as practical when the weather gets cold and icy. Instead of having your bike take up space in your home, consider hanging it from the ceiling of your garage, attic, basement, or other storage area! If youre looking for a simple way to hang up your bikes, try attaching a rubber hook to a ceiling joist and dangling your equipment by one wheel. If youre looking for a more convenient way to lift and lower your bikes, try using a pulley system instead!

[Edit]Steps

[Edit]Storing Bikes on Rubber Hooks

  1. Select a rubber or other non-metal hook to hold your bikes. Check your local hardware store or sporting goods shop to find a rubber hook, or a hook that isnt made of bare metal. Look for a piece of equipment thats about thick, so you can hang it in your storage area without it taking up too much space.[1]
    Hang Bikes from the Ceiling Step 1.jpg
    • Dont use metal hooks for long-term storage, as these can scrape and damage the wheels of your bike.
  2. Find a section of your ceiling that wont interfere with your vehicles. Search in your cellar, attic, garage or other storage area for a place where your bikes can stay for a long period of time. Depending on the height of your ceiling, you might not want to keep your bike in the center of your storage space.[2]
    Hang Bikes from the Ceiling Step 2.jpg
    • If you arent sure whether or not your bike will be able to fit safely to your garage ceiling, take a quick measurement of your ceiling, vehicle, and bikes height to make sure.
  3. Tap the ceiling with your hand to find the ceiling joists. Set up a ladder to reach the ceiling. If the surface is covered in drywall, tap around the ceiling to find a solid area. Once youve found a solid spot, mark it with a pencil or some other writing tool.[3]
    Hang Bikes from the Ceiling Step 3.jpg
    • Hollow areas will sound echoey when you tap on them, while solid areas will sound firm.
    • If your ceiling has beams instead of drywall, you dont have to worry about this.
    • If youre having difficulty finding the ceiling joists, you can also use a stud finder.
  4. Measure the hooks diameter to choose a proper drill bit. Examine the rubber hook that youre planning to hang from your ceiling. Measure the diameter of the screw, then select an electric drill bit thats about of the screws width. Always use a drill bit thats smaller in diameter than the hook that youre using. When the bit is slightly smaller, you can firmly and securely install the hook into the ceiling.[4]
    Hang Bikes from the Ceiling Step 4.jpg
    • If your drill bit is too large, your hook might be too loose.
  5. Create a pilot hole in the ceiling with an electric drill. Take your chosen bit and twist it into your drill. With a small amount of force, guide the drill into a solid section of beam. Use the entire length of the bit to create your pilot hole, then remove the device.[5]
    Hang Bikes from the Ceiling Step 5.jpg
  6. Screw your ceiling hook into the drilled pilot hole. Use your hands to push and twist the ceiling hook into the pilot hole. Turn the hook clockwise to secure it into the ceiling. If youre having trouble tightening the hook, stick a screwdriver horizontally through the curved portion of the hook and twist it like a vice.[6]
    Hang Bikes from the Ceiling Step 6.jpg
    • Continue twisting until the hook is secure, and no longer shifts or turns.
  7. Install a second hook if you want to hang your bike by 2 wheels. Measure the distance between the center axles of your bike wheels. Once your first hook is in place, use a tape measure to mark off that same distance from the initial hook. Drill a guiding hole through this mark, then twist a second bike hook into place.[7]
    Hang Bikes from the Ceiling Step 7.jpg
    • If youre planning on hanging up several bikes, use this measuring system to install multiple hooks.
  8. Wipe down your bike with a wet paper towel. Take a damp paper towel or disinfectant wipe and clean off any visible dust, sweat or grime from your bike. Try and clean off all sections of the bike, as you dont want any dust or debris falling and clogging up the chains and gears of your bike while it's in storage.[8]
    Hang Bikes from the Ceiling Step 8.jpg
    • Sweat can be commonly found on most bikes, especially if you use your equipment a lot. Try to wipe away sweat as soon as you see it, or it could drip further into your bike.
  9. Lift your bicycle and mount the wheel on the hook. Hold your bike from the center tube and bring it to the ceiling. Rotate your bike slowly, lifting the metal rim of the back wheel over the curve of the hook. Remove 1 hand at a time to make sure that your bike is secure.[9]
    Hang Bikes from the Ceiling Step 9.jpg
    • Theres nothing wrong with placing your equipment in an upside-down or perpendicular position.
  10. Mount both wheels if you have 2 hooks. Hold your bike from the center tube and lift it upwards. Rotate the equipment by 180 degrees, bringing both wheels up to the hooks. Place 1 wheel onto a ceiling hook at a time, making sure that the metal rim is resting over the rubber hook. Remove your hands gradually to make sure that the bike is in place.[10]
    Hang Bikes from the Ceiling Step 10.jpg

[Edit]Using a Pulley System

  1. Acquire a pulley kit from your local hardware store. Before you begin any construction in your storage area, head to a hardware store or sporting goods shop to purchase a bike pulley or bike hoist kit. These kits generally include 2 pulley brackets, 2 hooks, a length of cord, and the screws needed for installation. You can save a lot of time by purchasing these supplies in a bundle, instead of searching for each part individually.[11]
    Hang Bikes from the Ceiling Step 11.jpg
    • You can get a pulley kit for as low as $9.
  2. Tap the ceiling to locate the ceiling joists. Form a fist and knock on the ceiling of your storage area. Depending on the place youre storing your bikes, you might see visible beams and joists that you can use for your pulley system. If your ceiling is obscured or otherwise covered, tap on a specific area and listen for a firm or echoing sound. If the resonating sound is firm, then youve found a joist.[12]
    Hang Bikes from the Ceiling Step 12.jpg
    • Try measuring to find another ceiling joist, just to make sure.[13]
  3. Screw 1 pulley bracket into a ceiling joist with an electric drill. Arrange your metal bracket along the length of the joist where youd like your bike to hang. Dont worry about the exact measurements of your bike at this point. Instead, use your hand to hold the pulley in place, and use an electric drill to secure 4 screws into the corresponding bracket holes.[14]
    Hang Bikes from the Ceiling Step 13.jpg
    • Depending on your storage space, you might have difficulty attaching the screws in the joist right off the bat. In this case, use your drill bit to form as many pilot holes as there are openings in the bracket. This will make it easier for you to add screws later on.
    • Youll need bike measurements when attaching the second pulley bracket.
  4. Measure the width of your bike seat to the handlebars. Take a measuring tape and extend it from the back of your bike seat to the center of your handlebars. Write down this measurement or commit it to memory, as it will help you arrange and attach your second pulley bracket.[15]
    Hang Bikes from the Ceiling Step 14.jpg
    • The pulley system hooks along the back edge of your bike seat and the front your handlebars.
  5. Drill a pilot hole using the measurements from your bike. Use your measuring tape to determine your bikes length in relation to the first pulley. Arrange the pulley bracket along the same ceiling joist, centering it over the end of your bike measurement. Hold the bracket in place with your hand, using your electric drill to create pilot holes through the openings of the bracket.[16]
    Hang Bikes from the Ceiling Step 15.jpg
    • This process is the same as when you attached the first pulley bracket.
  6. Thread and knot the pulley cord through the second bracket. Pull a section of your pulley cord through the back opening of your bracket. Use a firm knot to keep the cord in place, so the pulley system is secure. Once youve knotted the rope, let the rest of the cord dangle.[17]
    Hang Bikes from the Ceiling Step 16.jpg
    • Figure-eight knots are good for this kind of project.
    • The hole for the pulley cord is separate from the openings for the screws. Look for the end of the pulley that has an extra opening to figure out where the cord goes.
  7. Attach the second pulley bracket using the pilot holes. With the cord looped through the back, arrange the metal bracket over the pilot holes that you drilled previously. Use an electric drill to attach screws through these openings. Continue applying pressure until the bracket is firmly secured to the ceiling.[18]
    Hang Bikes from the Ceiling Step 17.jpg
    • Dont attach any screws over the cord.
  8. Loop the cord through both pulley brackets and hooks. Slide the hook apparatus onto the length of cord that youre threading through the pulley system. Take the loose end of this cord and bring it up and over the circular wheel of the pulley. Next, drag the length of cord horizontally so it attaches to the second pulley. Slide the second hook onto the cord, then loop the end of the rope up and over the circular wheel of this pulley bracket.[19]
    Hang Bikes from the Ceiling Step 18.jpg
  9. Attach a heavy-duty adhesive hook to the wall. Pull off the backing paper from 1 side of the adhesive strip, then firmly press the sticky side of the strip to the wall. Next, remove the other section of backing paper from the adhesive. Take the back of the hook structure and press it firmly onto the sticky strip for several seconds to successfully set it up.[20]
    Hang Bikes from the Ceiling Step 19.jpg
    • Try choosing an adhesive hook with utility or heavy-duty on the label. While your pulley cord wont be that heavy, you dont want to use a flimsy hook.
    • Always follow the instructions on the hooks packaging.
  10. Tie any extra cord to the hook on the lower wall. Leave of cord dangling from the pulley, so you can securely lift and lower your bike from your storage area. Loop the extra cord around the wall hook, so you can unspool it whenever you need to access your bike. If you dont leave enough slack for your pulley system, your bike hoist might not function properly.[21]
    Hang Bikes from the Ceiling Step 20.jpg
    • If you have more than 1 pulley system hooked up in your storage area, be sure to have separate wall hooks to prevent the cords from tangling.
  11. Secure the hooks to the handlebars and bike seat. Take 1 hook and attach it beneath the back of your bike seat. Next, take the second hook and arrange it beneath the piping of your handlebars. Before you do anything else, check that these hooks are secure, and that they arent going to shift and separate from the bike.[22]
    Hang Bikes from the Ceiling Step 21.jpg
    • Ideally, your hooks should have a rubber seal. If your hooks are only made of metal, then they might scratch your handlebars.
  12. Pull on the cord to lift up the bike. Tug your cord at a 45-degree angle so the safety brake on your pulley system is released. Continue pulling on the cord to raise the bike until it reaches the ceiling of your storage area. Once youve lifted the bike, release the cord and loop it around the designated wall hook.[23]
    Hang Bikes from the Ceiling Step 22.jpg

[Edit]Things Youll Need

[Edit]Storing Bikes on Rubber Hooks

  • Rubber hooks
  • Electric drill
  • Drill bit
  • Screwdriver (optional)
  • Paper towel or wipe

[Edit]Using a Pulley System

  • Pulley brackets
  • Stud finder (optional)
  • Measuring tape
  • Screws
  • Electric drill
  • Pulley cord
  • Pulley hooks
  • Wall hooks

[Edit]References

  1. https://m.youtube.com/watch?v=0Rp-T1Niftg&t=0m10s
  2. https://www.roadbikerider.com/bicycle-storage-with-bike-hooks-d3/
  3. https://m.youtube.com/watch?v=kF32I8gENl4&t=0m47s
  4. https://m.youtube.com/watch?v=0Rp-T1Niftg&t=0m28s
  5. https://m.youtube.com/watch?v=kF32I8gENl4&t=1m2s
  6. https://m.youtube.com/watch?v=gv2ZVNpiJGU&t=0m28s
  7. https://m.youtube.com/watch?v=EeDrXaUbSuU&t=0m29s
  8. https://www.roadbikerider.com/bicycle-storage-with-bike-hooks-d3/
  9. https://m.youtube.com/watch?v=0Rp-T1Niftg&t=1m56s
  10. https://m.youtube.com/watch?v=gv2ZVNpiJGU&t=0m7s
  11. https://m.youtube.com/watch?v=fNI8_qjDewM&t=4m54s
  12. https://m.youtube.com/watch?v=kF32I8gENl4&t=0m46s
  13. https://m.youtube.com/watch?v=kF32I8gENl4&t=1m13s
  14. https://m.youtube.com/watch?v=kF32I8gENl4&t=1m31s
  15. https://m.youtube.com/watch?v=kF32I8gENl4&t=2m19s
  16. https://m.youtube.com/watch?v=kF32I8gENl4&t=2m31s
  17. https://m.youtube.com/watch?v=kF32I8gENl4&t=2m53s
  18. https://m.youtube.com/watch?v=kF32I8gENl4&t=3m5s
  19. https://m.youtube.com/watch?v=2qlK88gx9GU&t=3m12s
  20. https://m.youtube.com/watch?v=PuaECYj84FA&t=0m13s
  21. https://m.youtube.com/watch?v=kF32I8gENl4&t=4m51s
  22. https://m.youtube.com/watch?v=fNI8_qjDewM&t=4m54s
  23. https://m.youtube.com/watch?v=fNI8_qjDewM&t=6m11s

Older Post Newer Post